UPS 50 Standard Series
5-Phase, 5-Lead Stepping Motor and Driver Units

 
High torque output in a compact package.
High Resolution.
-- 0.72°/Full Step (500 step/rev)
-- 0.36°/Half Step (1000 step/rev)
Extremely smooth operation.
-- Virtually no low rpm resonance.
Motor and Driver are matched pair..
-- No current adjustments needed.
Easy hookup with only 5 leads.
Highly cost-effective.

 

 
UPS 50 Series
(A) after the Part Number denotes single shaft (Front shaft only) motor configuration.
(B) after the Part Number denotes thru shaft (Front & Rear shaft) motor configuration.

Motor Size(mm)

Motor and Driver Combination Part Number

Max. Holding Torque: oz-in (kg-cm)

Rotor Inertia oz-in2 (g-cm2)

Step Angle Full/Half

Phase Current (A)

Motor Weight: oz (kg)

Driver Part Number

Motor Part Number
Metric 23(60)
UPS50-564A(B)
UPS50-566A(B)
UPS50-569A(B)
31.94(2.30)
51.38(3.70)
105.54(7.60)
0.547(100.05)
1.093(199.90)
2.180(398.72)
0.72°/0.36°
0.72°/0.36°
0.72°/0.36°
0.75
0.75
1.40
17.60(0.50)
26.40(0.75)
45.80(1.30)
UPS50-031
UPS50-031
UPS50-131
PS564A(B)
PS566A(B)
PS569A(B)
Metric 34(85)
UPS50-596A(B)
UPS50-599A(B)
UPS50-5913A(B)
163.90(11.80)
290.20(20.90)
527.70(38.00)
3.820(700.03)
6.260(1200.0)
9.480(1800.0)
0.72°/0.36°
0.72°/0.36°
0.72°/0.36°
1.40
1.40
1.40
52.90(1.50)
88.20(2.50)
123.4(3.50)
UPS50-131
UPS50-131
UPS50-131
PS596A(B)
PS599A(B)
PS5913A(B)

 

 

Motor Specification

  

Driver Specification
        UPS50-031 UPS50-131
Accuracy ± 5 min.   Output Current 0.75 A per Phase Max. 1.4 A per Phase Max.
Shaft Radial Play 0.00098 in. max. / 1.1 lbs load   Driver Type Star Bi-Polar , Constant Current Chopper
Shaft Axial Play 0.00295 in. max. / 2.2 lbs load   Power Requirements 90 - 121 VAC , 50/60 Hz
Dielectric Strength No abnormality detected after the application of 0.5KV at 50 Hz between motor windings and frame for duration of one minute.   Power Consumption 2.0 A or less 3.5 A or less
Insulation Class Class B   Built in Functions Auto Current Down at stand still. Current OFF. Monitor Timing Output signal. Driver Overheat warning signal output.
Insulation Resistance 100 ohms or better with 500V potential applied between motor windings and frame at normal ambient temperature and humidity.   Input Pulse Type Step & Direction or Bi-Clock (CW/CCCW) pulses (Selectable). All Opto-Isolated . Voltage H=4.5 to 5V , L = 0 to 0.5V , Resistance = 220 ohms.
Operating Environment Temperature 0 ° C to +50 ° C   Dielectric Strength No abnormality detected after the application of AC 1 KV between case and power input terminals, case and signal I/O terminals, signal I/O terminals and power input terminals for duration of one minute.
      Insulation Resistance 100 M ohms or better with 500V potential applied between case and power input terminals and signal I/ O terminals.
      Operating Environment Temperature 0 ° C to +40 ° C