UPS 53 High Speed Series
5-Phase, 5-Lead Stepping Motor and Driver Units

 
Selectable Resolution.
-- 0.72°/Full Step (500 step/rev)
-- 0.36°/Half Step (1000 step/rev)
Speeds up to 14,000 rpm (233 rps)
Low inductance 5-phase motors are coupled with 2.8 amp high powered driver to provide further increased speed and acceleration capabilities over our standard UPS50 series motor/driver packages.
Extremely smooth operation.
-- Virtually no low rpm resonance.
Motor and Driver are matched pair..
-- No current adjustments needed.
Unit includes Motor & Driver with Built-in Power Supply.
Highly cost effective.

 
UPS 53 Series
(A) after the Part Number denotes single shaft (Front shaft only) motor configuration.
(B) after the Part Number denotes thru shaft (Front & Rear shaft) motor configuration.

Motor Size(mm)

Motor and Driver Combination Part Number

Max. Holding Torque: oz-in (kg-cm)

Rotor Inertia oz-in2 (g-cm2)

Step Angle Full/Half

Phase Current (A)

Motor Weight: oz (kg)

Driver Part Number

Motor Part Number
Metric 23(60)
UPS53-569HA(B)
105.5(7.60)
2.18(400)
0.72°/0.36°
2.8
45.80(1.3)
UPS53-331
PS566HA(B)
Metric 34(85)
UPS53-596HA(B)
UPS53-599HA(B)
UPS53-5913HA(B)
163.9(11.80)
290.2(20.9)
527.7(38.0)
3.82(700)
6.56(1200)
9.84(1800)
0.72°/0.36°
0.72°/0.36°
0.72°/0.36°
2.8
2.8
2.8
52.90(1.50)
88.20(2.50)
123.4(3.50)
UPS53-331
UPS53-331
UPS53-331
PS596HA(B)
PS599HA(B)
PS5913HA(B)
Metric 42(110)
UPS53-51117AD§
972.1(70.0)
49.20(9000)
0.72°/0.36°
2.8
299.8(8.50)
UPS53-331
PS51117AD§

§ = Single(front) shaft only.

 

Motor Specification   Driver Specification
        UPS53-331
Accuracy ± 5 min.   Output Current 2.8 A per Phase Max.
Shaft Radial Play 0.00098 in. max. / 1.1 lbs load   Driver Type Star Bi-Polar , Constant Current Chopper
Shaft Axial Play 0.00295 in. max. / 2.2.lbs load   Power Requirements 85 - 132 VAC , 50/60 Hz
Dielectric Strength No abnormality detected after the application of 0.5KV at 50 Hz between motor windings and frame for duration of one minute.   Power Consumption 7.0 A or less
Insulation Class Class B   Built in Functions Auto Current Down at stand still. Current OFF. Monitor Timing Output signal. Driver Overheat warning signal output.
Insulation Resistance 100 ohms or better with 500V potential applied between motor windings and frame at normal ambient temperature and humidity.   Input Pulse Type Step & Direction or Bi-Clock (CW/CCCW) pulses (Selectable). All Opto-Isolated . Voltage H=4.5 to 5V , L = 0 to 0.5V , Resistance = 220 ohms.
Operating Environment Temperature 0 ° C to +50 ° C   Dielectric Strength No abnormality detected after the application of AC 1 KV between case and power input terminals, case and signal I/O terminals, signal I/O terminals and power input terminals for duration of one minute.
      Insulation Resistance 100 M ohms or better with 500V potential applied between case and power input terminals and signal I/ O terminals.
      Operating Environment Temperature 0 ° C to +40 ° C